Pump Technology Catalogue 2019

8 DRAINMAJOR 60: The durable tank is manufactured from pol \HWKyOHQH , fully rigged with internal pipework and non return valve. QUALITY: The tank is pigmented throughout with an externally smooth isophthalic polyester gel coat and resin enriched lining. OUTLETS: The tank has a 1 " BSP male thread discharge outlet. (NRV supplied is female thread). PUMP Type PTL60: Vertical centrifugal type, single stage for submerged operation, with strainer base, open impeller (10 mm solids handling capacity). Motor: Fully encapsulated submersible motor with built-in overload/thermal cut-out, watertight (IP68) enclosure, class B insulation. Supplied with built-in level switch. Pump Casing: Plastic GFK pump body, top cover and GRP impeller, stainless steel encapsulated motor. Bearings: Combined shaft for motor and pump, mounted in grease lubricated ball bearings. Shaft Seal: Silicon carbide mechanical seal, unaffected by dry running for short periods. Fitted with mechanical seal and oil buffer chamber, the pumps will give reliable service for long periods with minimum supervision and maintenance, apart from regular cleaning of the tank and pump strainer. ALL INVERTS TO BE MADE TO SIDE OF TANK USING TANK CONNECTORS. 1¼" MINIMUM VENT TO AIR REQUIRED. IF DISHWASHERS, GLASSWASHERS OR WASHING MACHINES ARE USED A 2" VENT IS REQUIRED. The DRAINMAJOR 60 comes complete with a one year warranty. In the unlikely event of technical difficulties, please ring: Pump Technology Limited on 0118 9821555 The DRAINMAJOR 730 is recommended for kitchens where 30mm solids handling capacity is required (e.g. for sinks with waste disposal units). If your requirement is for commercial kitchens with multiple sinks, dishwashers, glasswashers etc. please use the DRAINKING. Due to a policy of continuous product improvement we reserve the right to alter specifications without notice. IMPORTANT: This unit is not designed to handle sewage. Please enquire about our packaged sewage pumping systems. INSTALLATION DRAINMAJOR 60 Installers please note. (use solvent weld or copper pipe) 1. Remove lid from tank, check pump is correctly positioned and connecting pipework has not been damaged in transit. 2. Check that the pump is correctly positioned in the tank and that the union is tightly connected so that the pump does not move on its mountings impeding the float action. 3. All inverts should be brought into the side of the tank by drilling a hole and using an appropriate tank connector. 4. All inverts should be brought into the tank (using tank connectors) at the highest possible level from the floor - i.e. no lower than 12 0 mm from base of unit. 5. Preferably no connections through the lid as this inhibits easy removal of the lid for cleaning tank. (Note: tank MUST be positioned in such a way that lid can be removed easily to allow access for tank interior and pump cleaning.) 6. Ensure that the inflow of water is not directed onto the float mechanism. 7. Slow radius bends MUST be used for every change of direction of the discharge pipework. 8. If the discharge pipework connects to a soil stack, manhole etc. below the discharge outlet of the tank , an anti-syphon unit MUST be fitted to the highest point of the discharge pipework. VENTING TO AIR: THE TANK MUST BE VENTED TO AIR (1¼" MIN.). DO NOT USE A DURGO / AIR ADMITTANCE VALVE . IF GLASSWASHERS OR COMMERCIAL/INDUSTRIAL DISHWASHERS/WASHING MACHINES ARE USED IT IS RECOMMENDED THAT AT LEAST A 2" VENT IS TAKEN TO AIR. (IF YOU WISH TO DISCUSS YOUR PARTICULAR APPLICATION WITH REGARD TO VENTILATION PLEASE CONTACT OUR TECHNICAL SALES DEPARTMENT.) MAINTENANCE: The DRAINMAJOR 60 should have the lid REGULARLY removed for CLEANING of the Tank and Pump PTL 60D 3-phase 400V 0.75kW 0.60kW 1.3A 2800 10mm Technical Data (50 Hz) Type P1 P2 F.L.C. RPM Overload Protection Max. Solids Size Voltage PTL 60E single phase 230 V 0.70kW 0.45kW 3.4A 2600 10mm Incorporated in motor (thermostat) Depending on the working environment of the DRAINMAJOR it may be advisable to fit a grease trap/interceptor. Please seek advice from our technical department.