24
DRAINMAJOR 60 DUO:
This consists of a durable tank
manufactured from polyester/glass fibre laminate.
QUALITY:
The tank is pigmented throughout with an
externally smooth isophthalic polyester gel coat and resin
enriched lining.
OUTLETS:
The tank has a 1½" BSP discharge outlet.
PUMPS X 2 Type PTL60:
Vertical centrifugal type, single
stage for submerged operation, with strainer base, open
impeller (10 mm solids handling capacity).
Motor:
Fully encapsulated submersible motor with built-in
overload/thermal cut-out, watertight (IP68) enclosure, class B
insulation. Supplied with built-in level switch.
Pump Casing:
Plastic GFK pump body, top cover and GRP
impeller, stainless steel encapsulated motor.
Bearings:
Combined shaft for motor and pump, mounted in
grease lubricated ball bearings.
Shaft Seal:
Pump end: silicon carbide mechanical seal,
uneffected by dry running.
Fitted with mechanical seal and oil buffer chamber, the
pumps will give reliable service for long periods with
minimum supervision and maintenance, apart from regular
cleaning of the tank and pump strainer.
ALL INVERTS TO BE MADE TO SIDE OF TANK USING
TANK CONNECTORS.
1¼" MINIMUM VENT TO AIR REQUIRED.
IF DISHWASHERS, GLASSWASHERS OR WASHING
MACHINES ARE USED A 2" VENT IS REQUIRED.
The
DRAINMAJOR 60 DUO
comes complete with a one year warranty.
In the unlikely event of technical difficulties, please ring:
Pump Technology Limited on 01189 821555
Due to a policy of continuous product improvement we reserve the right to alter specifications without notice.
IMPORTANT: This unit is not designed to
handle sewage. Please enquire about our
packaged sewage pumping systems.
Pump
performance
is subject to
ISO 2548
tolerances.
Capacity ± 8%
Head ± 6%
KW absorbed ± 8%
INSTALLATION
DRAINMAJOR 60 DUO
Installers please note:
1
Make sure there is a waste connection into each compartment, connections are made with tank connectors and should not be lower
than 200mm from the base unless a low level float* has been selected, then they can be lowered to 110mm.
2
As and when the water level in each compartment rises it will activate the pump. If one of pumps failed to operate the rising water
level will activate the Alarm trigger and then flow over the divider/weir into the opposite compartment to be pumped away by the
reserve pump. The alarm can be muted and the lid of the chamber removed, it may be obvious what the fault may be or it may be
necessary to give us a call.
3
The discharge is connection is 1½
"
male BSP.
4
A Vent pipe will also need to be fitted from the side of the unit at high level using a tank connector. This needs to be run to
air or high level and be fitted with a Pump Technology Ltd. Charco or Micro vent.
5
Do Not put connections through the lid as this makes maintenance and cleaning difficult.
6
The Pump power cables required a suitable fused connection.
7
The Alarm Box requires a 240v supply and should be wall mounted it comes complete with a re chargeable battery to warn of
power failure.
8
The Alarm triggers are fitted to the tank and the two-core cable, which can be extended, needs to connect to the Alarm box in the
terminals marked "Float".
9
The Terminal marked "Remote" is a volt free contact and can be used for a connection to a BMS.
*
This needs to be arranged at time of order as special build
.
VENTING TO AIR:
THE TANK MUST BE VENTED TO AIR (1½
"
MIN.). IF GLASSWASHERS OR
COMMERCIAL/INDUSTRIAL DISHWASHERS/WASHING MACHINES ARE USED IT IS RECOMMENDED THAT AT
LEAST A 2” VENT IS TAKEN TO AIR. (IF YOU WISH TO DISCUSS YOUR PARTICULAR APPLICATION WITH
REGARD TO VENTILATION PLEASE CONTACT OUR TECHNICAL SALES DEPARTMENT.)
MAINTENANCE: The DRAINMAJOR 60 DUO should have the lid REGULARLY removed for CLEANING of the Tank and Pump
Delivery Head/m
A - PTL 60E
240V
B - PTL 60D
3-Phase
1 2 3 4 5 6 7 8 9
16.5 15 14 12 10.5 8.5 6 3.5 m³ /h
18 17 15.5 14 12 10.5 8.5 6 2.5
PERFORMANCE PTL 60
TECHNICAL DATA 50 hz
Type
Voltage
P1
P2
F.L.C.
PRM Overload
Max. Solids
Protection
Size
PTL 60E (A) single phase 230 V 0.70kW 0.45kW 3.4 A
2600
Incorporated
10 mm
in motor
PTL 60D (B)
3-phase 400 V
0.75kW 0.60kW 1.3 A
2800
(thermostat)
10 mm
